A new technique precisely measures how two-dimensional materials expand when heated

كيف تتوسع المواد

Understand thermal expansion through the coupling temperature and the effect of the substrate on phonon modes. attributed to him: Science advances (2022). DOI: 10.1126/sciadv.abo3783

Two-dimensional materials, consisting of only one layer of atoms, can be packed together much more densely than conventional materials, so they can be used to make transistors, solar cells, LEDs and other devices that run faster and perform better.

One of the issues with these next-generation electronic devices is the heat they generate when in use. Conventional electronics usually reach about 80 degrees Celsius, however Materials 2D devices are packed so densely into a small space that devices can get twice as hot. this is temperature increase The device may be damaged.

This problem is exacerbated by the fact that scientists do not have a good understanding of how 2D materials expand when temperatures rise. Because the materials are so thin and optically transparent, their coefficient of thermal expansion (TEC)—the tendency of a material to expand when temperatures rise—is nearly impossible to measure using standard methods.

“When people measure the coefficient of thermal expansion of some bulk materialsThey use a scientific ruler or a microscope because with bulk matter, you have a sensitivity to measure. The challenge with 2D materials is that we can’t really see it, so we need to turn to another kind of ruler to measure TEC,” says Yang Zhong, a graduate student at Mechanical engineering.

Zhong is a co-author of a paper demonstrating such a “governor”. Instead of directly measuring how stretched a material is, they use laser light To track the vibrations of the atoms that make up matter. Taking measurements of a 2D material on three different surfaces or substrates allows the coefficient of thermal expansion to be extracted accurately.

The new study showed that this method is highly accurate and achieves results that match theoretical calculations. The approach confirms that TECs for 2D materials lie in a much narrower range than previously thought. This information can help engineers design Next generation electronics.

“By emphasizing this narrow material range, we give engineers a great deal of material flexibility to choose the bottom reactant when they design a device. They don’t need to invent a new underlayment just to relieve thermal stress. We believe this has very important implications for the electronic device and packaging community,” says co-author and former mechanical engineering graduate student Lin’an Zhang SM ’18, Ph.D. ’22, now a research scientist.

Co-authors include senior author Evelyn N. Wang, Ford Professor of Engineering and chair of MIT’s Department of Mechanical Engineering, as well as others from MIT’s Department of Electrical Engineering and Computer Science and MIT’s Department of Mechanical and Energy Engineering. Southern University of Science and Technology in Shenzhen, China. Research published in Science advances.

Measurement of vibrations

Because 2D materials are so small—perhaps only a few microns in size—standard instruments are not sensitive enough to measure their expansion directly. In addition, the materials are so thin that they must be bonded to a substrate such as silicon or copper. If the 2D material and its substrate have different TECs, they will expand differently when temperatures rise, causing thermal stress.

For example, if a 2D material is bonded to a substrate with a higher energy consumption (TEC) rate, when the device is heated, the substrate will expand more than the 2D material it is stretching. This makes it difficult to measure the actual TEC of a 2D material because the substrate affects its expansion.

The researchers got around these problems by focusing on the atoms that make up the two-dimensional matter. When a substance is heated, its atoms vibrate at a lower frequency and move away from each other, causing the material to expand. They measure these vibrations using a technique called Raman microspectroscopy, which involves hitting the material with a laser. The vibrating atoms scatter the laser light, and this interaction can be used to detect the frequency of their vibrations.

But as the substrate is stretched or compressed, it affects how the atoms of the two-dimensional material vibrate. The researchers needed to isolate this substrate effect to zero in the material’s intrinsic properties. They did this by measuring the vibrational frequency of the same 2D material on three different substrates: copper, which has a high TEC content; fused silica, which has a low electrical energy consumption ratio; A silicone substrate with small holes. Because the 2D material hovers over the holes on the latter substrate, it can perform measurements on these small regions of the freestanding material.

The researchers then placed each substrate on a thermal stage to precisely control the temperature, heat each sample, and perform microscopic Raman spectroscopy.

“By performing Raman measurements on the three samples, we can extract something called a temperature coefficient that depends on the substrate. Using these three different substrates, and knowing the TECs for fused silica and copper, we can extract the intrinsic TEC for 2D,” Chung explains.

Strange result

They performed this analysis on several 2D materials and found that they all match the theoretical calculations. But the researchers saw something they didn’t expect: the two-dimensional materials fell into a hierarchy based on the elements that made them up. For example, a 2D material containing molybdenum will always have more TEC than one containing tungsten.

The researchers dug deeper and learned that this hierarchy results from a fundamental atomic property known as electronegativity. Electronegativity describes the tendency of atoms to withdraw or withdraw electrons when they bond. It is listed on Periodic Table per item.

They found that the greater the electronegativity difference between the elements that make up a two-dimensional material, the lower the material’s coefficient of thermal expansion. An engineer can use this method to quickly estimate the typical electric consumption (TEC) rate for any two-dimensional material, rather than relying on complex calculations that normally have to be crunched by a supercomputer, Zhong says.

“An engineer can just look up the periodic table, get the electronegativity of the corresponding materials, plug it into our correlation equation, and within a minute can get a reasonably good estimate of the TEC. This is very promising for rapid material selection for engineering applications,” Zhang says.

Going forward, the researchers want to apply their methodology to many more 2D materials, possibly building a database of TECs. They also want to use Raman microspectroscopy to measure the TECs of heterogeneous materials, which combine several 2D materials. They hope to find out why the thermal expansion of two-dimensional materials differs from that of bulk materials.

more information:
Yang Zhong et al, A unified approach and characterization of thermal expansion of two-dimensional transition metal chalcogenide monolayers, Science advances (2022). DOI: 10.1126/sciadv.abo3783. www.science.org/doi/10.1126/sciadv.abo3783

the quote: New Technique Accurately Measures How 2D Materials Expand When Heated (2022, November 18) Retrieved November 19, 2022 from https://phys.org/news/2022-11-technique-accurately-2d-materials.html

This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without written permission. The content is provided for informational purposes only.

Leave a Comment